Breast Pump Rack for Bottle Washer Pro: Setup and Cleaning
By Baby Brezza UK | Published: 2026-10-16
Category: How-to Guides
Learn how to install the Breast Pump Rack in your Bottle Washer Pro, load pump parts correctly, and clean the rack without damaging it. A practical step-by-step guide.
Quick answer
To set up the Breast Pump Rack for Bottle Washer Pro, unplug the washer, remove the existing rack, and swap in the replacement top and bottom racks with the connecting tubes. Load pump parts on the top rack (up to 7 large valves/membranes) and run a normal cycle. Clean the rack weekly with warm soapy water, and never put it in the dishwasher.
Why a dedicated pump rack matters
Standard bottle racks hold bottles upright, but breast pump parts are small, lightweight, and easily flipped by spray jets. The Breast Pump Rack for Bottle Washer Pro is designed with a universal fit that works with all types and brands of breast pumps, including wearable pumps. Its top rack holds up to 7 large valves or membranes, keeping them secure so they get properly cleaned and dried. If you regularly wash pump parts alongside bottles, this accessory reduces the need for manual scrubbing and helps you get a full clean from every cycle.
What you need before you start
Gather your Breast Pump Rack kit (top rack, bottom rack, and connecting tubes), a clean towel, and your Bottle Washer Pro. Make sure the washer is unplugged and cool before you begin. If you are also replacing detergent or descaling tablets, now is a good time to check your supplies. The BUNDLE: Detergent Tablets + Descaling Tablets for the Bottle Washer Pro (product 2410386) includes 120 detergent tablets and descaling tablets made exclusively for the Bottle Washer Pro, which can help maintain performance after you install the new rack.
How to install the Breast Pump Rack step by step
Follow these steps in order to avoid misalignment or damage. Each step includes a checkpoint so you can confirm you are on track.
Step-by-step: install and clean your pump rack
- Unplug and empty the washer: Turn off and unplug the Bottle Washer Pro. Remove any bottles or parts from the current rack and set them aside. Pull out the existing top and bottom racks. Checkpoint: The washer should be completely empty and cool before you proceed.
- Insert the new bottom rack: Align the bottom rack with the guides inside the washer tub and press it down until it sits flat. It should not wobble. Common mistake: Forcing the rack if it does not seat easily. Check for any debris in the guides.
- Attach the connecting tubes: Push the connecting tubes onto the ports on the bottom rack. They should click or fit snugly. These tubes route water to the top rack. Checkpoint: Tubes must be fully seated; a loose tube will reduce spray pressure.
- Place the top rack: Set the top rack onto the tubes, aligning the openings with the tube ends. Press gently until it is stable. Common mistake: Installing the top rack upside down. The valve holders should face up.
- Load pump parts correctly: Arrange valves and membranes on the top rack, using the designated slots. You can fit up to 7 large valves or membranes. Place smaller parts like backflow protectors on the bottom rack if they fit securely. Checkpoint: Parts should not overlap or touch each other, so water can reach all surfaces.
- Run a test cycle: Plug in the washer, add a detergent tablet if desired, and run a normal cycle without bottles. Watch for proper spray arm rotation and drainage. If you see leaks or unusual noises, unplug and recheck the rack and tube connections.
- Clean the rack weekly: Remove the top and bottom racks and the connecting tubes. Wash them by hand in warm soapy water, rinse thoroughly, and air dry. Do not use abrasive cleaners or a dishwasher. Common mistake: Putting the rack in the dishwasher, which can warp the plastic and affect fit.
Product facts
- Breast Pump Rack for Bottle Washer Pro®: Universal Fit: Works with ALL types and brands of breast pumps - including wearable pumps. You can use the same rack no matter which pump brand you own, so you do not need to buy a separate accessory if you switch pumps.
- Breast Pump Rack for Bottle Washer Pro®: Top Rack Fit: Holds up to 7 large valves/membranes. You can clean a full day's worth of pump parts in one cycle without overcrowding, which helps water and air reach every surface.
- Breast Pump Rack for Bottle Washer Pro®: Complete Replacement Rack System: Includes top rack, bottom rack and connecting tubes - swap in easily for your existing Bottle Washer Pro® rack. You get everything needed to convert your washer for pump parts, and you can switch back to the standard rack whenever you prefer.
- BUNDLE: Bottle Washer Pro + Detergent Tablets (120pcs) - All Black: BUNDLE: Includes an additional box of 120 Detergent Tablets. Having extra tablets on hand means you can run pump-part cycles without worrying about running out, and the bundle can save money compared to buying separately.
